Aluminium Blue Water Cruiser Project

I want to see full spec & all the high res photos of this boat ,
Login or Register

Boat REF# 220635
Price
£19,500.00 (Approx US$25,293.45) ReducedUnder-Offer
Length 38'0"
Year 2012
Construction Aluminium
Underwater profile Long Keel
Engine 1 x diesel 80hp, Perkins M90 (2015)
Lying Plymouth

Make an offer

Contact the Broker

  • Contact Billy Hallam
  • Telephone +44(0)1752 426 106
  • Cell +44(0) 7973 675 261
  • Email billyhallam@boatshedplymouth.com

Gallery

I want to see full spec & all the high res photos of this boat , register me now or login

Extra Details

Designer Ganley Yachts, New Zealand
Builder Previous Owner, Isle of Wight
Lying Plymouth
Get quote for boat deliveries
Fuel capacity 176.0 USG Total - 2 Tanks
Water capacity 132.0 USG Total - 5 Tanks
Holding tank capacity 13.2 USG Total - 1 Tanks

Mechanical

Engine 1 x diesel 80hp
Engine make and model Perkins M90 (2015)
Engine Hours engine1:   00
Engine Cooled Indirect
Steering tiller
Drive shaft
Prop(s)
Fuel consumption (approx) Not Recorded

Perkins Factory reconditioned engine £5000
Engine hours = 0
New drive shaft
Batteries will be chargeable by engine & shore power

Possible to change steering from tiller to wheel - steering parts excluding wheel available.

Dimensions

Length 38'0"
LWL 33'0"
Beam 11'0"
Draft Min 6'7"
Draft Max 6'7"
Displacement 11,025.0lbs
Headroom 6'3"
Storage Ashore

Electrical Systems

24 volt,

Construction

Construction Aluminium
Underwater profile Long Keel
Finish Aluminium finish

Displacement figure approximate.
The owner believes there is the following outstanding work to be done on this project:
'The engine installation needs to be finished including the exhaust system, fuel system and controls.
The shaft seal needs to be installed e.g. Tides marine seal.
The prop needs to be obtained.
The Ballast needs to be fitted, washer punchings (3 tons required) and then the bilge pumps etc. can be done (on board ready).
Weld on hand rails.
The wiring is all there ready for connection."

Accommodation

Sink 1
Heads 1 heads (Manual)
Sink tick
Fridge tick
Pressurised water system tick
Non-Smokers tick

Double sink in galley
Heads fitted & plumbed with holding tank.

Deck Gear

Rode tick

1 anchors
(Delta 20kg)
196'10" of chain

Safety Equipment

5 bilge pumps (1 manual / 4 electric)

Bilge pumps need to be fitted

Broker's Comments

This sturdy partially fitted out aluminium hull has the potential to become a fantastic blue water cruising vessel, power or sail.

The unique stern was originally constructed by the previous owner to house a salvage winch for retrieving treasure in the Pacific Ocean.

A great deal of the expensive internal work has already been carried out by a professional engineer. She comes fitted with an 80 hp Perkins M90 at a cost of £5k, which is fully reconditioned and unused from the Perkins factory. A new prop shaft is also fitted and she has plenty of brand new tankage fitted for fuel, water and a holding tank for waste.

The galley is partially fitted with a double sink and fridge. The heads/wet room is also a work in progress with a new toilet & sink whilst a shower still needs to be purchased & fitted.

All Tru Design skin fittings are ABYC approved & rated H-27 standard for aluminium hulls.

Also included are 4 electric bilge pumps plus 1 manual, a battery charger, fresh water pumps and chain plates if needed.

This is a great opportunity to acquire a very reasonably priced, unused, aluminium hull and to finish it to your own desired specification.

These boat details are subject to contract.
Note: Offers on the asking price may be considered.

This Aluminium Blue Water Cruiser Project has been personally photographed and viewed by Billy Hallam of Boatshed Plymouth. Click here for contact details.
Disclaimer The particulars detailed herein are intended to give a fair description of the vessel but their accuracy cannot be guaranteed. These particulars are not and shall not form part of any offer or contract for the sale of the vessel and are supplied on the understanding that all negotiations shall be through Boatshed, who act as agents for the vendor. The vendor is not selling in the course of a business unless otherwise stated. The prospective purchaser is strongly recommended to check the particulars and, where considered appropriate, at his own expense, to employ qualified agents to carry out structural and/or mechanical and/or electrical surveys and inspections in order to assess the actual condition of the vessel before purchase.

If you like this boat we recommend